3.5″ inch ILI9486 TFT Touch Shield LCD Module 480×320 for Arduino Uno
In stock
₹859.00 (Incl. GST)3.5″ diagonal LCD TFT display, with bright 4 white-LED backlights, default state: on
It can control the backlight to connect the transistor to a digital pin
480×320 Pixels, with colorful and 18-bit, 262,000 different kinds of shade
4-wire resistive touchscreen
8-bit digital interface, plus 4 control lines
38Pin CP2102 ESP-32 WiFi + Bluetooth Development Board with Type-C USB Interface
Out of stock
Original price was: ₹492.00.₹450.00Current price is: ₹450.00. (Incl. GST)- Supply Voltage: 2.2 V ~ 3.6 V
- GPIO Pins: 38
- Current: 80 mA
- Data Rate: 54 Mbps.
- Flash Memory: 32Mbits
- Frequency: 2.4 GHz.
5MP Raspberry Pi 3/4 Model B Camera Module Rev 1.3 with Cable
In stock
₹284.00 (Incl. GST)Resolution: 5 MP
Interface Type: CSI(Camera Serial Interface)
Dimensions: 25x23x8 (LxWxH) mm
Supported Video Formats: 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 video
Fully Compatible with Raspberry Pi 3 and 4 Model B
Plug-n-Play camera for Raspberry Pi 3 and 4 Model B.
ADS1115 16 Bit I2C ADC Analog to Digital Converter Module
In stock
₹164.00 (Incl. GST)Specifications:
Single-shot mode: automatically turns off
Low current consumption: Continuous mode 150 μA
Wide supply voltage range: 2.0V to 5.5V
Interfacing is done via I2C
Programmable data rate: 8SPS to 860SPS
Low drift internal voltage reference
Internal Oscillator
Internal PGA up to 860 samples per second (SPS)
Four single-ended or two differential inputs (ADS1115)
Operating temperature: -40 ° C to + 140 ° C
Programmable comparator
ARDUINO LELY PAD BIG ATMEGA328P
Out of stock
₹372.00 (Incl. GST)Features
Microcontroller : ATmega168V or ATmega328V
Operating Voltage 2.7-5.5 V
Input Voltage 2.7-5.5 V
Digital I/O Pins 14 (of which 6 provide PWM output)
Analog Input Pins 6
DC Current per I/O Pin 40 mA
Flash Memory 16 KB (of which 2 KB used by bootloader)
SRAM 1 KB
EEPROM 512 bytes Clock Speed 8 MHz
Arduino Mega 2560 R3 Board A16U
In stock
₹1,177.00 (Incl. GST)Features
Microcontroller : ATmega2560
Operating Voltage : 5V
Input Voltage (recommended) : 7-12V
Input Voltage (limit) : 6-20V
Digital I/O Pins : 54 (of which 15 provide PWM output)
Analog Input Pins : 16
DC Current per I/O Pin : 20 mA
DC Current for 3.3V Pin : 50 mA
Flash Memory : 256 KB of which 8 KB used by bootloader
SRAM : 8 KB
EEPROM : 4 KB
Clock Speed : 16 MHz
LED BUILTIN : 13
Arduino Sensor Shield V5 Expansion Board
In stock
₹95.00 (Incl. GST)Quick Overview:
Retain the merits of the V4.0 version
Laminated design
PCB immersion gold processing technology
IIC interface
Bluetooth module communication interface
SD card module communication interface
APC220 wireless rf modules communication interface
RB URF v1.1 ultrasonic sensors interface
12864 LCD string of line and parallel interface
32 servo controller interface
Compatible With Arduino Uno
Arduino Uno R3 DIP
In stock
₹467.00 (Incl. GST)Arduino UNO R3 Development Board ATMEGA16U2 ATMEGA328P (DIP)
The Arduino Uno R3 is an open-source microcontroller board based on the ATmega328 chip. It features 14 digital input/output pins, 6 analog input pins, an onboard 16 MHz ceramic resonator, a USB connection port, a DC power jack, an ICSP header, and a reset button for the microcontroller. This board includes everything needed to support the microcontroller, making it easy to get started—simply connect it to a computer via a USB cable or power it with a DC adapter or battery.
Unlike previous models, the Uno does not use the FTDI USB-to-serial driver chip. Instead, it incorporates the Atmega16U2 (or Atmega8U2 up to version R2) as a USB-to-serial converter. The Arduino Uno can be powered through the USB connection or an external power supply, with the power source selected automatically.
External power can be supplied via an AC-to-DC adapter (wall-wart) or battery. The adapter connects through a 2.1mm center-positive plug into the board’s power jack, while battery leads can be connected to the GND and VIN pin headers of the power connector. The board can operate on an external supply ranging from 6 to 20 volts. However, if supplied with less than 7V, the 5V pin may output less than five volts, potentially leading to instability. Conversely, using more than 12V could cause the voltage regulator to overheat and damage the board. The recommended voltage range for the Arduino Uno is 5V to 12V.
Features
Operating Voltage: 5V
MCU: ATMEGA 328P
Input Voltage (recommended): 7-12V.
Input Voltage (limit): 6-20V.
Digital I/O Pins: 14
PWM Digital I/O Pins: 6
Analog Input Pins: 6
DC Current per I/O Pin: 40 mA
DC Current for 3.3V Pin: 50 mA
Flash Memory: 32 KB
Flash Memory for Bootloader: 0.5 KB
SRAM: 2 KB
EEPROM: 1 KB
Clock Speed: 16 MHz
Arduino Uno R3 with Cable
In stock
₹520.00 (Incl. GST)Specifications:
ATmega328 Controller
Digital IO 13
PWM Channel 6
Working Freq. 16MHz
DC current / IO 40mA
DC current / IO 50mA (3.3V)
Input Voltage 6V to 20V DC
Flash 32Kb
SRAM 2Kb
EEPROM 1Kb
ATTINY85 USB Development Board
In stock
₹242.00 (Incl. GST)Specification:
Support for the Arduino IDE 1.0 + (OSX/Windows/Linux).
Power via USB or External Source or 7-16 v to 5 v (automatic selection).
The Onboard, 150 ma 5 v Regulator.
Built-in USB and serial were debugging).
6 I/O Pins (2 inform the for USB only if your program actively communicates over USB, otherwise you can use all 6 even if you are programming via USB).
8 k Flash Memory (about 6 k after bootloader).
The I2C and SPI (vis USI).
The Power LED and the Test/Status LEDs.
Blue NANO IO Shield V1.0 Simple Expansion Board Finished Board
In stock
₹140.00 (Incl. GST)Specifications:
Compatible with Arduino NANO
It leads all pins out, which is convenient for wiring and doing experiments.
All digital and analogue pins breakout
Compact size
CH340G USB To TTL(Serial) Converter For Arduino Nano Raspberry Pi
In stock
₹59.00 (Incl. GST)- TTL interface output, easy to connect to your MCU.
- Dual 3.3V and 5V Power output, work with 3.3v and 5 V target device.
- The mini-module is designed specifically for STC download and ARDUINO PRO supports all series of STC
- Microcomputer with cold start reset button
- Supports WIN7/VISTA/MAC/LINUX(32 bit /64-bit system)
- Built-in USB to TTL Transfer chip.
- Designed to be used for USB to TTL electronic projects.