Showing 277–288 of 372 results
Shop
PC817 2 CH Optocoupler Isolation Module
In stock
₹73.00 (Incl. GST)Specification:
I/O Isolation for MCUs (Micro Controller Units)
Noise Suppression in Switching Circuits
Driving Port Signal Voltage: 3.6-24V
Output Port Voltage Port: 3.6-30V
Output Can Be Switched From Pull-Up or Pull-Down With Jumpers.
PCA9548A Low Voltage 8-Channel I2C Switch with Reset
In stock
₹90.00 (Incl. GST)Specifications:
Operating Voltage: 2.3 V to 5.5 V
Clock Frequency: 0 kHz to 400 kHz
Input Tolerance: 5 V
Package Options: SSOP, TVSOP, SOIC, TSSOP, VQFN
ESD Protection:
2000 V (Human-Body Model)
200 V (Machine Model)
1000 V (Charged-Device Model)
PICKIT 3.5 Debugger / Programmer
In stock
₹2,536.00 (Incl. GST)Specification :
USB (Full speed 12 Mbits / s interface to host PC)
Real-time execution
MPLAB IDE compatible (free download from Microchip)
built-in over-voltage / short circuit monitor
Firmware upgradeable from PC / web download
totally enclosed
Diagnostic LEDs (power, busy, error)
read/write program and data memory from a microcontroller
erase program memory with Verification
Freeze peripherals at a breakpoint
program up to 512K byte flash with the Programmer to Go
ICSP cable included
PIR Sensor Module HC-SR501
In stock
₹59.94 (Incl. GST)Wide Working Voltage Range: DC 4.5V- 20V
Current Drain: <60uA
Detection Angle: <140°
Detection Distance: 3 to 7m (can be adjusted)
Blockade time: 2.5s (Default)
Work temperature: -20-+80°C
PL2303 TA Download Cable USB to TTL RS232 Module USB to Serial
In stock
₹103.00 (Incl. GST)Specifications:
Built-in TTL COM PC-PL2303HX Chip.
Standard USB type and TTL 4 pin connector
Simple and Easy way to give USB support to your designs
Available for Linux, Mac, WinCE, and Windows (XP, 7), Win 8
Cable Length: 1Meter
Weight: 30gm
PL2303 USB To TTL(Serial) Converter Module
In stock
₹75.00 (Incl. GST)Specifications :
Adopt imported controller PL2303HX, which can stabilize the flash with high speed
500mA self-recovery fuse for protection.
Two data transmission indicator can monitor data transfer status in real time.
Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power.
The entire board is coated by the high quality transparent heat-shrinkable sleeve, making the PCB in insulation state from outside.
The electrostatic package ensures the board will not be damaged before use.
Support WIN7 system.
PM2.5 GP2Y1010AU0F Dust Smoke Particle Sensor
In stock
₹392.00 (Incl. GST)Features:
Power supply voltage: DC5 ± 2V
Sensitivity: 0.5V / (0.1mg / m3)
The minimum detection level of particles: 0.8 m
Clean air voltage: 0.9V typ.
Low consumption current (Icc: MAX. 20 mA)
The presence of dust can be detected by the photometry of only one pulse
Enable to distinguish smoke from house dust
PN532 NFC RFID module V3, NFC with Android phone extension of RFID provide Schematic and library
In stock
Original price was: ₹399.00.₹380.00Current price is: ₹380.00. (Incl. GST)Specifications:
Easy to change mode: with a small SMD toggle Switch, it becomes very easy to change among IIC, SPI, and HSU modes
Longer distance: the reading distance becomes 5~7cm, compared with 4~6 cm of the last version
Built-in PCB Antenna, with 5cm~7cm communication distance
On-board level shifter, Standard 5V TTL for I2C and UART, 3.3V TTL SPI
Work as an RFID reader/writer
Work as a 1443-A card or a virtual card
Compatible with Arduino Board.
Pro Micro 5V 16M Mini Leonardo Microcontroller Development Board For Arduino
In stock
₹450.00 (Incl. GST)ATMEGA32U4 running in 5V / 16MHz
Support Arduino IDE V1.0.1
Micro USB interface programming on the board
Four 10-bit ADC pin
12 digital I / O (5 PWM capability)
Rx and Tx hardware serial connection
Pro Mini ATMEGA328P 3.3V/8M (Official Version)
In stock
₹210.00 (Incl. GST)specifications:
Microcontroller: ATmega328
Circuit Operating Voltage: 3.3V
Clock frequency: 8MHz.
Digital I/O Pins: 14
8 analog input port: A0 ~ A7.
A pair of TTL level serial port transceiver : RX / TX.
6 PWM port: D3, D5, D6, D9, D10, D11.
Support serial download.
Proto Screw Shield 1.0 For Arduino Uno
In stock
₹226.00 (Incl. GST)Specifications:
Arduino terminal to provide the IO, port connection.
3.81 posts quality, reliable, convenient, durable.
Combined with the Proto Shield, the middle can be used as a prototype expansion board.
Double-sided PCB Prototyping extended area vias connecting the front sides can be welded components.
The middle section can be placed small bread plate, convenient test extend
PS2 Joystick Module Breakout Sensor
In stock
₹40.00 (Incl. GST)specifications:
2 potentiometers for 2 axes
Connector: +5Vcc – GND – VRx – VRy – SW
Dimensions:4 X 2.6 X 3.2CM
1 x switch