Showing 229–240 of 372 results
Shop
MAX485 TTL To RS485
In stock
Original price was: ₹30.00.₹25.00Current price is: ₹25.00. (Incl. GST)Specifications :
Operating voltage: 5V
On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver.
A low power consumption for the RS-485 communication
Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring.
All pins of the chip have been lead to can be controlled through the microcontroller.
Convenient RS-485 communication wiring
Multiple Units can be connected to the same RS-485 bus wiring.
MAX6675 Module with K Type Thermocouple Sensor Temperature
In stock
₹310.00 (Incl. GST)Specifications:
Module uses MAX6675 IC which can handle readings from 0°C to 1024°C
Supplied thermocouple probe rated for up to 80°C with 1/4″ -20 threaded tip
0.25°C resolution, ±3°C accuracy
Uses 3-wire SPI interface
3 – 5.5V operation
MAX6675 Thermocouple Sensor Module
In stock
₹264.00 (Incl. GST)Specifications:
Working voltage: DC-5V
Operating Current: 50mA
Temperature measuring range: -2°C to 800 °C
Temperature measurement accuracy: ± 1.5 °C
Temperature resolution : 0.25 °C
The output mode: SPI digital signal
Storage temperature: -20 ~ 80 °C
MAX7219 Dot Led Matrix Module MCU Control LED Display Module
In stock
₹124.00 (Incl. GST)Specifications:
Voltage Supply (Vs):4.0V ~ 5.5V
Supply current:330mA
Segment drive source current:10mA
Shut down current:150uA
Scan rate:500-1300Hz, 800Hz
Operating temperature (MAX7219E):40°C ~ 85°C
Dimension 32 x 32 x 1.5 cm (L x W x H) (Single Module)
Dot Led Matrix Module incorporating MAX7219 Driver chip
Requires only 3 communication wires of MCU
Cascading multiple Matrix LED Module is very easy
The size of the display is very compact
The PCB features M3 holes for mounting.
Compatible With Arduino Board, Raspberry pi
MAX98357 I2S 3W Class D Amplifier Interface Audio Decoder Module Filterless Board For Raspberry Pi ESP32
In stock
Specifications:
3.2 W output at 10% THD, 4 Ω impedance of the speaker and 5 V power supply
2.7 – 5.5 V operating voltage
77 dB PSRR at 1 kHz
Selectable gains: 3 dB, 6 dB, 9 dB, 12 dB, 15 dB
MCP2515 CAN Module TJA1050 Receiver SPI 51 Single Chip Program Routine Arduino
In stock
₹91.00 (Incl. GST)Specifications :
Input Supply voltage: 5V
Input Supply Current: 5 mA
Communication Rate: 1 Mbps
Support CAN V2.0B technical standard, communication rate 1Mb / S.
0 to 8 bytes long data field.
Use High-speed CAN transceiver TJA1050
SPI control for expanding Multi CAN bus interface
Use serial port could view the communication data
With the independent key, LED indicator, Power indicator
With power pin
Positioning screw hole center spacing 23 mm x 38 mm
The working current: typical 5mA, standby current 1 microamp. Except for the power indicator.
MCU-758 Hall Current Sensor ACS758LCB-050B- PFF-T Linear Current Sensor Module
In stock
₹440.00 (Incl. GST)Specifications:
Working voltage: 3V-5V (MAN SV)
Static output voltage: VCCi2
Working current: 135m2A (MAX)
Small in size, with easy mounting capability.
Monolithic Hall IC for high reliability
Mega +WiFi R3 Atmega2560+NodeMCU ESP8266 32Mb Memory USB-TTL CH340G Compatible For Arduino Mega
In stock
₹1,335.00 (Incl. GST)Specifications:
Microcontroller:ATmega2560
IC Wi-Fi : ESP8266
USB-TTL converter: CH340G
Power Out: 5V-800mA
Power Input USB: 5V (500mA max.)
Power Input VIN/DC Jack: 9-24V
Power Consumption: 5V 800mA
Logic Level: 5V
Wi-Fi 802.11 b/g/n 2.4 GHz
USB: Micro USB
Clock Frequency: 16MHz
Operating Supply Voltage: 5V
Digital I/O: 54
Analog I/O: 16
Memory Size: 256kb
Data RAM Type/Size: 8Kb
Data ROM Type/Size: 4Kb
Interface Type : SerialOTA
Operating temperature :−40С°/+125С°
Dimensions:53.361×101.86mm
Buil-inexternal antenna
MG811 Carbon Dioxide Sensor For Carbon Dioxide Detector Module
In stock
₹2,475.00 (Incl. GST)Specifications:-
Sensor Type: Gas Sensor
Chip: MG811
Gas Sensitive: Carbon Dioxide
Operating Voltage (V): 6V DC
Dimensions: 3.2×2.2×2.9 cms
Weight: 10 grams
Micro SD Card Reader Module
In stock
₹51.00 (Incl. GST)Power Supply: 4.5V – 5.5V, 3.3V
Positioning Holes: 4 M2 screws positioning hole diameter of 2.2mm
Control Interface: GND, VCC, MISO, MOSI, SCK, CS
Size: 45 x 28mm
Net weight: 6g
Mini MP1584 DC-DC 3A Adjustable Buck Module
In stock
₹50.00 (Incl. GST)Specifications:
Input Voltage: 4.5V – 28V
Output Voltage: 0.8V – 20V
Output Voltage Adjustment: On-board potentiometer
Max. Output Current: 3A
Typical Output Voltage : 1.8A
Ceramic Capacitor Stable
Internal Soft-Start
Internally Set Current Limit without a Current Sensing Resistor.
Mini USB ATmega32U4 Pro Micro 5V 16MHz Board Modules
In stock
₹450.00 (Incl. GST)Microcontroller: ATmega32U4, 16MHz
Memory: 32KB Flash, 2.5KB SRAM
USB: Mini USB for power and communication
GPIO: Digital, analog, and power pins
USB: Direct USB HID functionality