Showing 493–504 of 1108 results
Shop
Filter by brands
AdafruitAdafruit 1- Atmel 1
- DOAT 1
- FLYSKY 1
- FUTABA 1
- IDEAL 8
- Johnson 8
- MASTECH 1
- OMRON 5
- OZO 1
- POSH 1
- Raspberry Pi 3
- SanDisk 2
- Seeed Studio 2
- SOLDRON 6
- Tower Pro 5
WaveshareWaveshare 6
CJMCU-4051 74HC4051 8 Channel Analog Multiplexer/Demultiplexer Breakoutut Board for Arduino
In stock
₹79.00 (Incl. GST)Specifications
Wide Analog Input Voltage Range: +/-5V
Low “ON” Resistance: 80 ohm (type) at Vcc = 4.5V; 70 ohm (type) at Vcc = 6.0V; 60 ohm (type) at Vcc = 9.0V.
Logic Level Translation: to enable 5V to communicate with +/-5V analog signals
Board Size: 30 x 19 mm
CJMCU-75 LM75B LM75 Temperature Sensor Module Digital I2C Breakout
In stock
₹155.00 (Incl. GST)Features:
I2C bus interface, the device address 7 slave address 1001xxx, can expand external eight devices on the same bus;
11bit ADC provides a temperature resolution of 0.125’C;
Programmable temperature threshold and hysteresis set points;
In order to reduce power consumption, the current consumption in shutdown mode is the only 1.0uA;
On power-up, the device can be used as a stand-alone temperature controller
CJMCU-9833 AD9833BRMZ Programmable Sine Triangular Square Waveform Generator Module
In stock
₹495.00 (Incl. GST)Working voltage: 2.3V-5.5V.
Working temperature range: -40 ~ + 105.
Onboard 25MHZ (accuracy of 50ppm) active crystal.
On-board high-speed amplifiers
CJMCU-GUVA-S12SD Sunlight Ultraviolet Ray Intensity UV Sensor
In stock
₹239.00 (Incl. GST)Specifications:
Power supply voltage of 2.5 V ~ 5 V
Low power consumption
Wide detection range: 240 nm to 370 nm
Wide Angle: 130 degrees
Schottky type photosensitive diode
Good linear response
High sensitivity
CJMCU-TEMT6000 An Ambient Light Sensor
In stock
₹100.00 (Incl. GST)Features:
AEC-Q101 qualified
High photosensitivity
Near-Human Eye Spectral Response
Scalable Output Voltage
Adapted to human eye responsivity
Lead (Pb)-free reflow soldering
CNC 4 Axis Controller DSP Controlled – TB6560 Stepper Motor
Out of stock
₹5,399.00 (Incl. GST)Features:
High performance, cost-effective.
Automatic idle-current reduction.
Supply voltage up to 45V DC.
Output current up to 5.0A.
Suitable for 2-phase and 4-phase motors.
High speed optoelectronic isolation signal input.
Single-chip PWM bipolar sinusoidal chopper ensures low vibration and high efficiency.
1, 2, 4, 8, 16 adjustable micro step control, motors run more precisely and smoothly.
Overload, overcurrent, overheat, overvoltage and under voltage protection to avoid damaging your computer and devices.
Single-chip PWM bipolar sinusoidal chopper ensures low vibration and high efficiency.
With one 0 ~ 10V PWM Signal output port for speed adjustment and one Relay output port.
5 types of input control in manual control interface, to set Limit, Estop, Midpoint-Setting, Cutter-presetting/Tool-Setting etc..
CNC Shield V3 Arduino Uno Mega Compatible
In stock
₹121.54 (Incl. GST)Specifications:
Interfaces with Arduino Uno.
4 stepper motor driver outputs, 3 Axis + 1 Slave.
Compatible with Pololu A4988 and DRV8825 stepper drivers and others.
6 Limit switch inputs.
I2C and UART outputs.
Additional connections available for Spindle Control, Stop/Start & Emergency Buttons.
Fully tested after assembly.
CNC Shield V4.0 3-Axis Stepper Motor Drive Board
Out of stock
₹178.00 (Incl. GST)Features :
3 Axis stepper motor driver.
Compatible with a micro-drive laser engraving machine, three-axis CNC engraving machine.
2A can be controlled within the two-phase four-wire stepper motor.
Power DC5V interface, 7.5-12V voltage input.
GRBL compatible.
Worked with Arduino nano.
Cnlinko LP-20 Male 4 Pin Waterproof Power Connector Plastic+Metal Shell Solder Terminal IP67 500V 20A
In stock
₹480.00 (Incl. GST)- MPN: LP-20-C04PE-01-022
- Brand: CNLINKO
Combo PH Electrode Probe + PH Value Detection Sensor Module 5V DC Arduino Compatible – Economy
In stock
Original price was: ₹1,800.00.₹1,749.00Current price is: ₹1,749.00. (Incl. GST)Specifications:
Operating Voltage: 5V DC
Optimal Operating Temperature: ~25°C
Interface: BNC connector for PH Probe
Controller Connection: Analog port of Arduino or compatible controller
Indicator: Blue LED power indicator
Compatibility: Arduino and similar microcontrollers
Measurement Method: Immersion in standard solution, reading via serial monitor
Reusable: Probe can be washed for repeated measurements
CP2102-GMR USB to UART Bridge IC | High-Speed Serial Converter for Embedded Systems & Microcontrollers
In stock
₹195.00 (Incl. GST)Specifications:
Manufacturer: Silicon Labs
Model: CP2102-GMR
Function: USB to UART Bridge
Interface: USB 2.0 Full-Speed (12 Mbps)
Baud Rate: Up to 1 Mbps
Operating Voltage: 3.0V – 3.6V
Package Type: QFN-28
Features:
Integrated voltage regulator and oscillator
Low power operation
No external crystal required
USB suspend/resume support
Operating Temperature: -40°C to +85°C
Applications: Embedded systems, USB-to-serial communication, microcontroller interfacing, data logging, and IoT devices